Calendario

Diciembre. 2017
LunMarMierJueVierSabDom
 << < > >>
    123
45678910
11121314151617
18192021222324
25262728293031

Anuncio

¿Quién está en línea?

Miembro: 0
Visitantes: 3

rss Sindicación

Oct292016

09:37:35

ikea assembly

ikea kitchen design


Kitchen Cabinet Set up - Step-By-Step Instructions regarding how to Install Kitchen Cabinets On your own


Since you've got your new kitchen area cabinets, you will be all set to maneuver on for the up coming big step.....Setting up your kitchen cabinets. Though the particular set up of your Kitchen area Cupboards isn'tall that tough, the essential 1st action is measuring and marking out the place the cupboards will go. By placing structure markings to the partitions and flooring, it'll not only assist you to with kitchen area cupboard placement and stud destinations, nevertheless it may also enable you to find in which adjustments and shims are going to be necessary. Right before we begin you will find a pair of things that you will want for your project:


Pencil


Stage or Laser Amount


Drill


Tape Evaluate


Stud Finder


Clamps


1" x 3" Piece of lumber (6'-8' in length) or an Inverted U-shaped frame (see notes down below)


Shims


Screws (very long more than enough to go 1 1/2 in the studs)


Utility knife or chisel


Marking Compass


An extra established of palms (you may need to bribe just one of the good friends)


As I mentioned earlier mentioned, you might have the choice of utilizing a piece of 1' x 3' lumber for the installation or developing a body to guidance the cupboards (I have provided an image of the sample body below). This may be made out of 2' x 4's and may be tall ample to support the bottom of the wall cupboards. In the event you system on putting in multiple kitchen, then I might propose the frame, but a bit of lumber will do just fantastic if it is a a single time occasion. In both case, you'll will need a different established of fingers to help you while using the set up.


In such a case we acquired (RTA) Ready-To-Assemble Kitchen area Cabinets from RTA Kitchen area & Bathroom Cabinet Store. Now the kitchen area cabinets are assembled, we are completely ready to start marking out our layout lines. Some people start with the base cabinets, but we are going to start while using the wall cupboards initial. There is no right or wrong way to start, I just prefer to start with all the upper cupboards 1st.


one. Use a amount and a pencil to draw a parallel line across the wall about three inches up from the floor. Measure down from this line, to the floor, and find the floors high point (if it has a person), and mark a line at that point. From that high point, Evaluate up 34 1/2 inches and draw a amount line across the wall to designate the top in the base cupboards.


two. Since you've got the top on the base cupboards marked, evaluate up yet another 19 1/2 inches and a level line across the wall to indicate the bottom with the wall cupboards. Lightly mark each cabinets' dimensions and placement about the wall to make sure that your original structure is correct.


three. Use a stud finder to track down the wall studs. Use a pencil to mark the stud areas at least 6 inches over and down below the line with the base with the wall cupboards. Draw straight vertical lines between the top and base marks to indicate the center of your studs.


4. If you decided to go along with the bit of 1' x 3' lumber, now is where you might use (in the event you decided to go together with the U-shaped frame, it can come into play after all your lines are laid out). Screw a temporary 1' x 3' support rail into the wall, aligning the top edge with the rail together with the line to the base edge of the wall cabinets. Attach it by driving 3 or 4 two inch screws through the rail in the wall studs.


5. Now that we have all the lines marked, it is time to start putting in your kitchen cabinets. We are going to start along with the corner cabinet (here is in which your helper's further established of fingers will likely be needed). Place the corner cupboard onto the temporary help rail and have your helper hold the corner cabinet in place. Drill pilot holes through the sturdy cupboard back or its assist rail and into your wall studs. Screw the cupboard into the wall utilizing two screws that are very long sufficient to penetrate the studs by at least 1 1/2 inches. Check the top in the cupboard for stage and the front of the cupboard for plumb. For those who really need to correct the position, just back the screws out a little bit and top shims behind the cabinet at the stud destinations. If it is plumb and level, drive the screws all the way in and add several far more into each stud to ensure that the cabinet is secured tightly to your wall.


6. Now we are going to maneuver onto the cupboards on either side in the corner cabinet. As you set up each 1, use the clamps to secure each cupboard to your neighboring cupboard and then check it for plumb with your degree. On faceframe cupboards, it is often a good idea to drill two 1/8 inch pilot holes through the sides in the faceframe and use screws. In such a case, with frameless, ready-to-assemble kitchen cupboards we are going to screw through the plywood sides and use shims in between the cabinets to ensure a tight fit and make sure that the cupboard faces are plumb.


7. After all the wall cabinets are in place, put in the corner or end base circumstance cabinet. Use shims wherever needed to stage the cupboard and raise it up on the line which indicates the high point on the floor. Be sure it is level from front to back and from side to side, then screw it to the wall studs. In the event you don't have a diagonal corner cupboard or blind base cupboard in the corner, push the adjoining cupboard into place and clamp the two units together. Add a filler strip if needed to allow the doors and drawers adequate clearance to open and close properly. If necessary, tap shims under the cabinet and behind it to adjust for plumb and level.


8. Drive screws through the cupboard back (and shims) into your wall studs. Trim any excess material from the shims with a sharp chisel or knife. Continue to add adjoining cupboards on this manner, joining them the same way you connected the wall cabinets in action 6.


9. If your cabinets end up butting against yet another wall, you could possibly will need a filler strip to make up the last few inches. If you have custom cupboards, they need to have been built to fill this gap, but should you are working with stock or RTA Kitchen area Cupboards the filler strip could be needed. If you do require to use a filler strip, leave the last cabinet detached from the other cupboards. Clamp a straightedge for the face of the nearest installed unit, extending far more than enough for you to put alignment marks within the end wall. Allow a 3/4" offset behind those marks (with the thickness in the filler piece) and fasten a cleat to your wall. Then install and fasten the last cupboard and measure the gap between its face body and the wall.


If the wall is flat, simply rip the filler board on the expected width and fasten it in place. If the wall is irregular, you'll have to scribe-fit the filler board. Start by setting a marking compass towards the width of the gap, then place a strip of 1"-wide masking tape along the filler board in the area the place it needs to be trimmed. Clamp the board to your end cabinet's face body, then trace the wall contour together with the compass. Remove the board and cut along the scribe line with a jig saw, then reinstall it to check the fit. When it's right, drive screws through the adjacent face body to the edge of your filler board. Screw or nail the other side for the cleat.


At this point, your kitchen cupboard set up is complete. In the event you purchased matching crown molding or any other details, these really should be easily installed now. Depending on whether you had to use shims under the base cupboards, it's possible you'll need to put in some trim pieces by the toe kicks to cover up the shims or any gaps at the underside on the kitchen area cabinets.


I hope this helps make your kitchen cupboard set up as smooth as possible. In case you will need any help with cabinet selection, kitchen area structure tips, or ideas for cupboard styles, check out RTA Kitchen & Bathroom Cupboard Store.

Admin · 24 vistas · Escribir un comentario

Vínculo permanente hacia el artículo completo

http://tamelabraaten.hazblog.com/Primer-blog-b1/ikea-assembly-b1-p522.htm

Comentarios

Este artículo no tiene Comentario por el momento .....


Escribir un comentario

Estatuto de los nuevos comentarios: Publicado





Se mostrará tu URL


Por favor introduce el código contenido en las imágenes.


Texto del comentario

Opciones
   (Salvar el nombre, el mail y la URL en los cookies)