Calendario

Diciembre. 2017
LunMarMierJueVierSabDom
 << < > >>
    123
45678910
11121314151617
18192021222324
25262728293031

Anuncio

¿Quién está en línea?

Miembro: 0
Visitantes: 3

rss Sindicación

Oct292016

09:29:16

ikea installers

ikea installers


Kitchen Cabinet Installation - Step-By-Step Recommendations regarding how to Set up Kitchen Cabinets By yourself


Now that you've your new kitchen cabinets, you are all set to maneuver on into the next significant move.....Putting in your kitchen area cupboards. Although the actual set up in the Kitchen Cupboards isn'tall that tough, the important first phase is measuring and marking out where by the cupboards will go. By placing format markings on the partitions and flooring, it's going to not simply assist you to with kitchen area cupboard placement and stud destinations, but it surely can even assist you track down wherever adjustments and shims will likely be essential. Right before we get going there are a couple of things that you will need to the task:


Pencil


Level or Laser Level


Drill


Tape Evaluate


Stud Finder


Clamps


1" x 3" Bit of lumber (6'-8' in length) or an Inverted U-shaped body (see notes below)


Shims


Screws (very long plenty of to go 1 1/2 to the studs)


Utility knife or chisel


Marking Compass


An extra set of fingers (it's possible you'll really have to bribe 1 within your close friends)


As I discussed previously mentioned, you have got the choice of using a piece of 1' x 3' lumber for that set up or building a body to support the cupboards (I've included a picture of the sample frame beneath). This may be made out of 2' x 4's and may be tall sufficient to guidance the bottom of the wall cabinets. For those who strategy on putting in multiple kitchen area, then I'd propose the body, but a chunk of lumber will just do good if that is a 1 time occasion. In both situation, you'll require yet another established of arms that will help along with the set up.


In this case we acquired (RTA) Ready-To-Assemble Kitchen area Cupboards from RTA Kitchen area & Bathroom Cabinet Store. Now the kitchen cupboards are assembled, we are all set to start marking out our format lines. Some people start together with the base cabinets, but we are going to start with the wall cabinets initial. There is no right or wrong way to start, I just prefer to start with the upper cupboards very first.


one. Use a amount and a pencil to draw a parallel line across the wall about three inches up from the floor. Evaluate down from this line, towards the floor, and find the floors high point (if it has one), and mark a line at that point. From that high point, Evaluate up 34 1/2 inches and draw a stage line across the wall to designate the top of the base cabinets.


2. Given that you might have the top of your base cupboards marked, measure up one more 19 1/2 inches and a level line across the wall to indicate the underside in the wall cupboards. Lightly mark each cabinets' dimensions and placement around the wall to make sure that your original layout is correct.


3. Use a stud finder to find the wall studs. Use a pencil to mark the stud locations at least 6 inches over and beneath the line with the base of your wall cupboards. Draw straight vertical lines between the top and base marks to indicate the center of your studs.


4. If you decided to go along with the piece of 1' x 3' lumber, now is the place you'll use (if you decided to go with the U-shaped body, it will eventually come into play after all your lines are laid out). Screw a temporary 1' x 3' guidance rail on the wall, aligning the top edge on the rail using the line for the base edge of your wall cupboards. Attach it by driving 3 or 4 two inch screws through the rail into the wall studs.


5. Since we have all the lines marked, it is time to start putting in your kitchen cupboards. We are going to start along with the corner cupboard (here is in which your helper's further established of hands will likely be needed). Place the corner cupboard onto the temporary assistance rail and have your helper hold the corner cabinet in place. Drill pilot holes through the sturdy cupboard back or its aid rail and to the wall studs. Screw the cupboard into the wall applying two screws that are prolonged plenty of to penetrate the studs by at least one 1/2 inches. Check the top from the cupboard for stage and the front of your cupboard for plumb. In the event you have to correct the position, just back the screws out a little bit and top shims behind the cupboard at the stud spots. If it is plumb and degree, drive the screws all the way in and add several much more into each stud to ensure that the cabinet is secured tightly towards the wall.


6. Now we are going to maneuver onto the cupboards on possibly side on the corner cupboard. As you install each one, use the clamps to secure each cabinet for the neighboring cupboard and then check it for plumb with your level. On faceframe cupboards, it is actually a good idea to drill two 1/8 inch pilot holes through the sides of the faceframe and use screws. In such a case, with frameless, ready-to-assemble kitchen area cupboards we are going to screw through the plywood sides and use shims in between the cabinets to ensure a tight fit and make sure that the cabinet faces are plumb.


7. After all the wall cupboards are in place, install the corner or end base case cupboard. Use shims exactly where needed to level the cabinet and raise it up into the line which indicates the high point on the floor. Be sure it is stage from front to back and from side to side, then screw it towards the wall studs. For those who don't have a diagonal corner cupboard or blind base cupboard in the corner, push the adjoining cupboard into place and clamp the two units together. Add a filler strip if needed to allow the doors and drawers sufficient clearance to open and close properly. If necessary, tap shims under the cupboard and behind it to adjust for plumb and level.


8. Drive screws through the cabinet back (and shims) into the wall studs. Trim any excess material from the shims with a sharp chisel or knife. Continue to add adjoining cupboards during this manner, joining them the same way you connected the wall cabinets in phase 6.


9. If your cabinets end up butting against an additional wall, you could require a filler strip to make up the last few inches. If you have custom cupboards, they must have been built to fill this gap, but for those who are working with stock or RTA Kitchen Cupboards the filler strip may be needed. In case you do need to use a filler strip, leave the last cupboard detached from the other cabinets. Clamp a straightedge to your face from the nearest installed unit, extending far enough for you to put alignment marks within the end wall. Allow a 3/4" offset behind those marks (for the thickness of your filler piece) and fasten a cleat on the wall. Then put in and fasten the last cabinet and evaluate the gap between its face frame and the wall.


If the wall is flat, simply rip the filler board to your expected width and fasten it in place. If the wall is irregular, you'll have to scribe-fit the filler board. Start by setting a marking compass for the width of the gap, then place a strip of 1"-wide masking tape along the filler board in the area in which it needs to be trimmed. Clamp the board to your end cabinet's face frame, then trace the wall contour with all the compass. Remove the board and cut along the scribe line with a jig saw, then reinstall it to check the fit. When it's right, drive screws through the adjacent face body to the edge in the filler board. Screw or nail the other side for the cleat.


At this point, your kitchen cupboard installation is complete. In case you purchased matching crown molding or any other details, these need to be easily installed now. Depending on whether you had to use shims under the base cabinets, chances are you'll really need to set up some trim pieces by the toe kicks to cover up the shims or any gaps at the underside of the kitchen area cupboards.


I hope this helps make your kitchen area cupboard installation as smooth as possible. In case you need to have any assist with cabinet selection, kitchen area layout tips, or ideas for cabinet styles, check out RTA Kitchen & Bathroom Cupboard Store.

Admin · 23 vistas · Escribir un comentario

Vínculo permanente hacia el artículo completo

http://tamelabraaten.hazblog.com/Primer-blog-b1/ikea-installers-b1-p520.htm

Comentarios

Este artículo no tiene Comentario por el momento .....


Escribir un comentario

Estatuto de los nuevos comentarios: Publicado





Se mostrará tu URL


Por favor introduce el código contenido en las imágenes.


Texto del comentario

Opciones
   (Salvar el nombre, el mail y la URL en los cookies)