Calendario

Octubre 2017
LunMarMierJueVierSabDom
 << < > >>
      1
2345678
9101112131415
16171819202122
23242526272829
3031     

Anuncio

¿Quién está en línea?

Miembro: 0
Visitantes: 3

rss Sindicación

Oct292016

09:35:32

ikea installers

ikea kitchen cabinet installers


Kitchen Cupboard Installation - Step-By-Step Directions on how to Set up Kitchen Cupboards Oneself


Since you've got your new kitchen cabinets, you are completely ready to move on for the following huge step.....Installing your kitchen cupboards. Even though the particular installation in the Kitchen area Cabinets isn'tall that arduous, the critical 1st step is measuring and marking out in which the cupboards will go. By placing structure markings around the partitions and floors, it can not just allow you to with kitchen cabinet placement and stud areas, nevertheless it can even help you identify wherever adjustments and shims are going to be expected. In advance of we start out you will find a couple of things that you'll want with the challenge:


Pencil


Level or Laser Level


Drill


Tape Measure


Stud Finder


Clamps


1" x 3" Piece of lumber (6'-8' in length) or an Inverted U-shaped frame (see notes beneath)


Shims


Screws (long ample to go 1 1/2 in to the studs)


Utility knife or chisel


Marking Compass


An extra set of arms (chances are you'll really need to bribe one particular within your buddies)


As I mentioned above, you've the option of employing a piece of 1' x 3' lumber for the installation or building a body to support the cupboards (I've integrated a picture of a sample frame under). This can be made from 2' x 4's and should be tall adequate to aid the bottom of the wall cupboards. In the event you approach on installing more than one kitchen, then I might recommend the frame, but a bit of lumber will do just wonderful if that is a one particular time celebration. In both scenario, you might want a further established of palms to assist together with the set up.


In such a case we acquired (RTA) Ready-To-Assemble Kitchen Cupboards from RTA Kitchen & Bathroom Cupboard Store. Now the kitchen cabinets are assembled, we are prepared to start marking out our format lines. Some people start together with the base cupboards, but we are going to start with the wall cupboards first. There is no right or wrong way to start, I just prefer to start along with the upper cabinets initially.


1. Use a stage and a pencil to draw a parallel line across the wall about 3 inches up from the floor. Evaluate down from this line, towards the floor, and find the floors high point (if it has a single), and mark a line at that point. From that high point, Measure up 34 1/2 inches and draw a level line across the wall to designate the top of your base cabinets.


two. Given that you've the top in the base cupboards marked, evaluate up one more 19 1/2 inches and a degree line across the wall to indicate the bottom of your wall cupboards. Lightly mark each cabinets' dimensions and placement on the wall to make sure that your original format is correct.


3. Use a stud finder to locate the wall studs. Use a pencil to mark the stud places at least 6 inches earlier mentioned and down below the line for your bottom from the wall cupboards. Draw straight vertical lines between the top and base marks to indicate the center from the studs.


4. In the event you decided to go with the bit of 1' x 3' lumber, now is in which you'll use (when you decided to go along with the U-shaped body, it's going to come into play after all your lines are laid out). Screw a temporary 1' x 3' support rail towards the wall, aligning the top edge from the rail while using the line with the base edge in the wall cupboards. Attach it by driving 3 or 4 two inch screws through the rail in to the wall studs.


5. Now that we have all the lines marked, it is time to start setting up your kitchen area cupboards. We are going to start together with the corner cabinet (here is where by your helper's extra established of arms are going to be needed). Place the corner cabinet onto the temporary support rail and have your helper hold the corner cupboard in place. Drill pilot holes through the sturdy cupboard back or its help rail and into the wall studs. Screw the cabinet into the wall using two screws that are extensive sufficient to penetrate the studs by at least 1 1/2 inches. Check the top of the cabinet for level and the front with the cabinet for plumb. For those who need to correct the position, just back the screws out a little bit and top shims behind the cupboard at the stud places. If it is plumb and level, drive the screws all the way in and add several a lot more into each stud to ensure that the cupboard is secured tightly into the wall.


6. Now we are going to maneuver onto the cupboards on possibly side on the corner cabinet. As you put in each one particular, use the clamps to secure each cabinet to your neighboring cabinet and then check it for plumb with your amount. On faceframe cupboards, it is usually a good idea to drill two 1/8 inch pilot holes through the sides of your faceframe and use screws. In such a case, with frameless, ready-to-assemble kitchen area cabinets we are going to screw through the plywood sides and use shims in between the cabinets to ensure a tight fit and make sure that the cupboard faces are plumb.


7. After all the wall cabinets are in place, set up the corner or end base scenario cupboard. Use shims in which needed to amount the cupboard and raise it up to your line which indicates the high point from the floor. Be sure it is level from front to back and from side to side, then screw it for the wall studs. If you don't have a diagonal corner cupboard or blind base cabinet in the corner, push the adjoining cupboard into place and clamp the two units together. Add a filler strip if needed to allow the doors and drawers adequate clearance to open and close properly. If necessary, tap shims under the cabinet and behind it to adjust for plumb and stage.


8. Drive screws through the cabinet back (and shims) into your wall studs. Trim any excess material from the shims with a sharp chisel or knife. Continue to add adjoining cabinets in this particular manner, joining them the same way you connected the wall cupboards in stage 6.


9. If your cabinets end up butting against one more wall, you might need a filler strip to make up the last few inches. When you have custom cupboards, they should really have been built to fill this gap, but for those who are using stock or RTA Kitchen area Cupboards the filler strip may possibly be needed. In case you do want to use a filler strip, leave the last cabinet detached from the other cupboards. Clamp a straightedge for the face with the nearest installed unit, extending far plenty of for you to put alignment marks around the end wall. Allow a 3/4" offset behind those marks (for that thickness on the filler piece) and fasten a cleat to your wall. Then install and fasten the last cabinet and evaluate the gap between its face frame and the wall.


If the wall is flat, simply rip the filler board to your necessary width and fasten it in place. If the wall is irregular, you'll really need to scribe-fit the filler board. Start by setting a marking compass to the width with the gap, then place a strip of 1"-wide masking tape along the filler board in the area exactly where it needs to be trimmed. Clamp the board for the end cabinet's face body, then trace the wall contour while using the compass. Remove the board and cut along the scribe line with a jig saw, then reinstall it to check the fit. When it's right, drive screws through the adjacent face frame in the edge with the filler board. Screw or nail the other side towards the cleat.


At this point, your kitchen cupboard set up is complete. For those who purchased matching crown molding or any other details, these need to be easily installed now. Depending on whether you had to use shims under the base cabinets, you could possibly must put in some trim pieces by the toe kicks to cover up the shims or any gaps at the bottom with the kitchen area cupboards.


I hope this helps make your kitchen area cupboard installation as smooth as possible. Should you have to have any assist with cupboard selection, kitchen area structure tips, or ideas for cupboard styles, check out RTA Kitchen area & Bathroom Cabinet Store.

Admin · 15 vistas · Escribir un comentario

Vínculo permanente hacia el artículo completo

http://tamelabraaten.hazblog.com/Primer-blog-b1/ikea-installers-b1-p521.htm

Comentarios

Este artículo no tiene Comentario por el momento .....


Escribir un comentario

Estatuto de los nuevos comentarios: Publicado





Se mostrará tu URL


Por favor introduce el código contenido en las imágenes.


Texto del comentario

Opciones
   (Salvar el nombre, el mail y la URL en los cookies)